top of page

Email us at

BCR Project Bike : Monster Tracker 2012

Finally finished one of our project bikes, Monster Tracker. The bike started off as a 07 Ducati Monster S2R 800 with a little over 8K miles on it. We always wanted to work on something modern for a change, so we picked it up over a year ago. First few months i would just use it as a daily commuter, but after awhile got bored of the stock look, stock sound of the exhaust, and that dime a dozen look, so we decided to do some custom work to it. First we were going to make it into a cafe racer, but we wanted to do something different for a change. We decided to take the bike apart, and turn it into a tracker/urban scrambler with a little steam punk flare.

Ducati-Flat-Tracker-3_silodrome.jpg

When we were designing the gas tank, we were having problems with coming out with a narrow tank that we want. The stock air box was huge, and the stock battery location was on top of the motor, middle of the bike. So if we made a narrow gas tank and have it mounted at the conventional location, the tank will be very small, and could only hold not even 2 gallons of gas. To get that narrow look that we want, we decided to make a gas tank under the seat and made it run all the way to the back of the bike. Kinda like what the what some modern adventure bikes has. With a long narrow tail gas tank, we were able to make a gas tank that holds close to 4 gallons of gas. We made the gas tank out of aluminum and shaped it to follow the tail part of the stock Monster trellis frame. We even widen the back part of the gas tank so we could hold more gas, and to give the tail part of the bike that old school cafe/tracker look.  We placed the gas cap at the usual location, in front of the seat, and made a front cover out of aluminum to cover the air box, battery and  other electrics of the bike. When we shaped the front cover, we followed the frame rails, and made it to look as if its the gas tank. We even added knee indents to give it that old school look. 

When we got the bike, the stock plastic tank was swollen and the last owner adjusted the steering stopper all the way out so the trees wouldn't hit the stock swollen plastic tank when you turn the front wheel. The turning radius of the monster is small as it is, and with the steering stopper pushed all the way out, its was hard to maneuver the bike especially in traffic. When we took the bike apart to see what we have to work with, the bike looks really nice without the huge tank, and the wide seat. So we decided to make the bike as narrow as we could just like the old school trackers.

MTRACK.jpg
MTRACK1.jpg

When we decided to make the aluminum gas tank under the seat, we had to make sure that the seat isn't touching the tank. So when the rider sits on the bike, there isn't any load put on the gas tank, that can cause the gas tank to crack and leak gas. We made a frame for the seat out of 1/4" flat bar, and mount it on the bike's frame, floating with at least 1/4" of space between the seat and the gas tank. Once we have the frame of the seat mounted, we made a shell for the seat pan out of fiberglass, and then have it upholstered out of black leather with old style double stitch. And to protect the tail of the gas tank, and to give that rugged off road look,  we made a stainless grill that wrapped around the top tail section of the gas tank. 

MTRACK2.jpg

Since we are going for that tracker style look, we covered the front end of the bike with flat aluminum and shaped it like a MX number plate. We wanted to use this bike in the street so we put in a small headlight, mount it off center, and hand hammered an aluminum headlight ring and surrounded it with stainless bottom head screws. 

MTRACK3.jpg

To get that the tracker theme, we opted to make a 2 into 2 high side exhaust. We made the back part header run towards the front of the bike, then have it exit on the throttle side of the bike. The front header was an easy set up. We just had to make sure that front header follows the back header pipe.  The whole exhaust is made of stainless with aluminum heat shield. Surprisingly with the proper foot wear, the exhaust doesn't get that hot even in traffic. 

MTRACK4.jpg

Fenders are made of fiberglass to save weight, and for faster time construction. We wanted to make the front fender look as light as possible, so we made the fender frame out of stainless rods, and have them mounted at the bottom of the forks. The rear fender, we wanted it to be mounted just like the old school British Scrambler. We added a round off tube at the back of the frame, and have the hand hammered aluminum tail light wrapped around the round off tube,  and then made it to securing the tail part of the rear fender. 

MTRACK5.jpg

Foot pegs on the bike are made of stainless, and we shaped it MX style, but with less aggressive teeth. We also made the foot controls out of stainless to match the pegs. We also made the heel guards out of stainless rods to match the stainless rack that's on the tail of the tank..

MTRACK7.jpg

The stock tapered bars on the monster was nice, but it was low. We wanted it higher, more of a MX look, so we switched  to a Pro tapered bars with medium lift. The Pro Tapered bars bolted right on the stock risers.

MTRACK6.jpg

We didn't do any mods to the engine other than cosmetics. The power of the stock 800cc motor is more than enough for what we have in mind for the bike. Even the wet clutch system is great especially riding the bike in the traffic. The only thing we did to the motor is we just polished the engine side covers, valve covers and cam end covers. Having them polished i think gave the V twin ducati motor some detail, and an old school look. Engine management, we added a power commander to compensate for the modified free flow exhaust and air pod filters.

MTRACK8.jpg

Doing this project we found out that Ducati monster are great platform for any custom bike setup, be it cafe style or tracker/scrambler. Overall we are happy with how this project, Monster Tracker, came out.  The bike is now lighter and narrow, and a lot easier to handle. Plus with all the custom parts that we did, we were able to make the parts mount on to the bike without making any modifications to the frame. In the future we might change the tires to a more rugged enduro tracker type tires. 

The pics were taken by Ben Chan of Blacksheep Photography. Stay tune for vids!

M1.jpg
M3.jpg
M5.jpg
M7.jpg
M9.jpg
M2.jpg
M4.jpg
M6.jpg
M8.jpg
M10.jpg
M11.jpg
  • Facebook Social Icon
  • Instagram Social Icon
bottom of page